Restart first: pull the power lead, wait, plug it back in. It keeps the network name and Wi-Fi password. Hold the reset pinhole only when the restart fails, because a factory reset erases both, as the setup guide does.
Restart or factory reset
The reset button is the eraser, not the fix. On a NETGEAR router it wipes the admin password, the SSID and the Wi-Fi security settings, and the login falls back to admin with the password password. A restart keeps all three.
Vendors use different labels for it — Restore Factory Settings, Factory Default Restore, Restore — and each returns the unit to its factory state.
Unplugging is a power cycle, so does unplugging a router reset it is no: the settings survive. Starlink's Gen 2 is the printed exception, six fast replugs.
Restart in the right order
The power cable comes out at the router end and the modem end, and the order is not interchangeable. Both printed sequences power the modem first, the router second.
The WAN port takes the modem's Ethernet cable; the power lead goes in last.
- Pull the router's power lead, then the modem's.
- Wait. Starlink prints two to three seconds between replugs on a Gen 2; Xfinity holds power out fifteen.
- Plug the modem back in and let its lights settle.
- Plug the router back in. On a TP-Link Archer AX10, a flashing power LED means it is still starting.
- Join the Wi-Fi with your existing password.
On a Verizon CR1000A router, a fast white blink means booting, solid white is normal; see modem-to-router connection.
Factory reset with the pinhole
The pinhole is a small recessed hole on the back or bottom. Press it with a paperclip only while the router is on, and keep the power on unless the steps take it out first.
Holds run from 5 to 30 seconds, but past 15 seconds a Google Wifi point flashes orange and aborts, while a DIR-878 wants 7, not the series' 10.
| Maker | Reset type | Printed hold | Signal it took |
|---|---|---|---|
| NETGEAR | Restore Factory Settings button, back | 7 seconds | Resets after release |
| TP-Link | Reset or WPS/Reset button | More than 10 seconds | SYS LED slow flash to quick flash |
| Linksys | Admin page or Reset button | About 10 seconds | Release the button |
| Asus | Admin page or RESET button | 5 to 10 seconds | Power LED flashes |
| D-Link DIR series | Pinhole, back; base on the DIR-878 | About 10 seconds; 7 on the DIR-878 | Power LED orange, reboot |
| Nest Wifi | Button, underside | 10 seconds | Light flashes, then solid yellow |
| eero | Reset button | About 15 seconds | LED flashes red |
| Starlink | App slider; Gen 2 power cycles | Six replugs, 2 to 3 seconds apart | Slider completes, STARLINK returns |
| Xfinity gateway | Reset pinhole, back | 15 seconds unplugged, 30 seconds plugged in | Lights flash, turn solid when ready |
| Xfinity XB2/XB3 | Reset pinhole, back | 30 seconds | Lights flash, solid when ready |
| Verizon Router | Rear Reset button | 15 seconds (guide: 10) | Resets, powers back on |
Read the signal, not the clock: release on the LED shift or colour change.
Save these settings first
The reset erases the SSID, both passwords and the Internet settings, and all devices drop at once.
Record these first:
- Wi-Fi name and password.
- Admin password.
- Connection type and any PPPoE or static address.
- Port forwards and reservations.
- Devices needing re-pairing.
Wi-Fi and admin values revert to those on the router label — on Verizon, admin included — while the D-Link admin password returns blank.
Use the backup control where offered: Restore/Save/Upload Setting on Asus, Backup and Restore on TP-Link.
Reset from the admin page
The admin page resets without a paperclip: Linksys under Troubleshooting, Diagnostics, Reset; Asus under Administration, Restore/Save/Upload Setting; TP-Link under Advanced, System Tools, Backup and Restore.
Apps match: Factory reset network in Google Home, Remove in eero, the Factory Reset slider in Starlink. Sign in via router login; if it will not open, use the pinhole.
A Starlink in bypass mode cannot be reset from the app; an eero needs internet before any reset, app or button.
When neither works
Go in three steps: restart, admin-page reset, pinhole. If a restart fixes nothing, split wired from wireless before wiping, as router not connecting sets out.
A reset does not roll back firmware; use the firmware update screens.
If the pinhole does nothing, read the light: on a Verizon CR1000A, slow red blink is a hardware fault, fast red is overheating or a failed system update.
Questions
Is it a good idea to reset a router?
Not for a stall. Restart first; a reset erases the Wi-Fi name, password and your rules, and reconnecting takes longer.
Can I press the reset button on my router?
Yes, it is the factory reset, not a restart. Hold only the printed 5 to 30 seconds and watch the LED.