Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

How to set up a VPN on a router

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
A VPN client on the router puts every LAN device behind the tunnel.

By RouterPanel Editorial · Updated

Short answer

Check the router's specification for a VPN client, then open the admin page behind the login and load a WireGuard or OpenVPN profile from your provider. One profile can cover every device you add to its list.

Check the router's specification for a VPN client, open its admin page behind the login and load a WireGuard or OpenVPN profile from your provider. One profile can cover every device you add to the router's list, phones and televisions alike.

What client mode changes

Teal: the SSID and key stay as they are; the change sits at the WAN port.

A router carries two VPN roles. The server lets a remote person dial in; the client dials out to a provider, so traffic from every listed device leaves through the tunnel.

That is the appeal: a television, a console and a doorbell with no VPN app are covered by one connection. On a Deco mesh the tunnel runs on the main unit even when a satellite does not support it.

Check the router first

Not every router can do this. TP-Link prints that not all of its routers support the VPN Client feature, and some models carry the server role alone. ASUS is blunter: if the feature is not in the specification table, there is no support. Read the table before you buy and the menu after you log in. ASUS also offers Instant Guard for remote access and prints the models that support it: RT-AX, RT-AXE and RT-BE series among them.

Pass-through is the trap: it only lets VPN packets of that type cross the router, with neither a client nor a server. The ASUS RT-AX92U is the printed example: IPsec pass-through, no IPsec server, no IPsec client.

On TP-Link the client page sits under Advanced > VPN Client at tplinkwifi.net; the MR and TL-MR series use another host. How to log in to your router covers the sign-in.

The admin path per maker

No two admin pages agree on where the switch lives. The table gives each printed path, protocol and role, from vendor pages of 18 November 2026.

The VPN screen per maker, the protocol offered and the role, checked 18 November 2026
Maker and exampleMenu pathProtocol on the screenRole offeredLimit or scope printed
TP-Link travel router, TL-WR1502XAdvanced > VPN Server > OpenVPN, tick EnableOpenVPNServerone example model
TP-Link Archer AX55Advanced > VPN Server > WireGuard, tick EnableWireGuardServerthe example model only
TP-Link router with the client featureAdvanced > VPN Client at tplinkwifi.netOpenVPN, PPTP, L2TP/IPsec; WireGuard on select models onlyClientanother host on the MR and TL-MR series
ASUS routerVPN > VPN Server > OpenVPN button, off by defaultOpenVPNServervaries by model
ASUS routerVPN > VPN Server > IPSec VPN button, then set Enable IPSec VPN Server to onIPSecServervaries by model
ASUS routerVPN > VPN Fusion > add icon to create a profileprovider profileClientfirmware 3.0.0.4.388.xxxxx or later; the model must list VPN Fusion
NETGEAR routerADVANCED > Advanced Setup > VPN Service, Enable, ApplyOpenVPNServerOpenVPN client 2.7.1 or earlier
D-Link router in the Quick VPN articleFeatures > Quick VPN, with L2TP over IPsec enabledL2TP over IPsecServerrouters with Quick VPN
Synology SRM routerVPN Plus Server > Standard VPN > OpenVPN > EnableOpenVPN; also SSTP, L2TP/IPsec, PPTPServerVPN Plus Server package; supported models
Synology SRM routerNetwork Center > Internet > Connection > VPN SettingsL2TP where offeredClientnot printed
UniFi GatewayVPN section of the Network applicationserver: OpenVPN, WireGuard, L2TP; client: OpenVPN, WireGuardBoth8 VPN clients; a gateway or Cloud Gateway is required, Next-Gen for the client
Linksys Dual-Band routerno VPN page in the article; pass-through on by defaultnone printedNeitherpass-through only

A provider config file needs a client row: TP-Link's client page, ASUS VPN Fusion, Synology's VPN Settings or UniFi. None means the flash.

Pick the protocol

Two protocols matter for a provider profile, WireGuard and OpenVPN, but the menus are wider: TP-Link's client page lists four protocols, and Synology's client guide recommends L2TP. The WireGuard project calls its protocol simple, fast and modern. OpenVPN describes itself as a full-featured SSL VPN over SSL/TLS.

Availability decides first. NETGEAR's server speaks OpenVPN only, and only to client builds 2.7.1 or earlier, as of 18 November. Take the protocol the provider issues, and take WireGuard when it offers both: fewer fields and nothing to tune.

Load the profile and connect

Red: leave the reset pinhole alone; a factory reset wipes the profile.

Amber: keep the modem cable in the WAN port and work from a laptop on a LAN port, so the session survives a WAN drop.

Download the profile from the provider's router section, not the phone one:

  1. Open the VPN Client screen from the table and sign in.
  2. Add the profile: upload the file or paste the keys the provider issued.
  3. Check the DNS setting: TP-Link prints that its routers do not support a separate DNS server address with a VPN, so the profile's setting stands.
  4. Save, then enable the tunnel.
  5. Run a DNS leak test; if your home address shows, switch off the fallback DNS and IPv6.

On ASUS the add icon under VPN Fusion is the profile slot, and on TP-Link the tick box is the enable. A guest network is not covered on its own: the tunnel follows the Device List, so add its devices there too.

Should you put a VPN on the router at all

One tunnel covers every listed device, and that is the trade: all of them share one exit address and one point of failure.

It is right when the devices cannot hold an app: a television, a console, a doorbell. It is wrong when you want the tunnel on for one device and off for the rest and the maker offers only a single on/off switch: TP-Link selects clients through its Device List, but the enable switch is per profile.

Banking and streaming sites can answer a provider address with a challenge page, and an outage there takes the house offline, because the WAN route now ends inside the tunnel.

What it costs in speed

The router encrypts with the same processor that runs the radios, so throughput falls.

Neither project page prints a price: Not printed, so cost is not the tie-break. No vendor page here prints a throughput figure, so measure beside and behind the tunnel.

TP-Link prints 16 accounts and 10 online at once for PPTP and L2TP, 16 concurrent for WireGuard and 10 for OpenVPN on its server range, as of 18 November 2026; a model can allow fewer. UniFi's VPN Client supports up to 8 clients.

Firmware if the router has no client

Red: a flash is the one step that can kill the box, so plan it and never start on a laptop battery.

OpenWRT on a Linksys MBE70 is one printed route: an SSH and script job, not a stock web page, for that model only. How to update your router's firmware covers the stock update first.

Check four things before choosing a build: the model and hardware revision, the flash size, the recovery method, whether the build keeps a VPN client. A wrong image boots to a dead LAN. Keep the old firmware file and the cable in.

Where the specification table is silent, the flash is the only route left; a router that cannot be recovered should not be flashed.

Questions

Do routers have built-in VPN?

Some do, far more as a server than as a client. TP-Link states that a few of its models support the server function only, and the client feature is missing on others. Read the specification table for the words VPN Client; pass-through is not it.

What is the downside of using a VPN?

Speed falls, the whole house shares one exit and one provider, and an outage takes every device offline.

Sources

  1. tp-link.com: 3799 · checked Nov 19, 2026
  2. tp-link.com: 4090 · checked Nov 19, 2026
  3. tp-link.com: 3135 · checked Nov 19, 2026
  4. asus.com: 1008713 · checked Nov 19, 2026
  5. asus.com: 1043769 · checked Nov 19, 2026
  6. asus.com: 1051131 · checked Nov 19, 2026
  7. asus.com: 1044123 · checked Nov 19, 2026
  8. kb.netgear.com: How do I enable the VPN feature on my NETGEAR router using a Windows computer · checked Nov 19, 2026
  9. support.dlink.com: FAQView.aspx?f=HFJkeFYpUTB%2FiHXOY7k%2BJw%3D%3D · checked Nov 19, 2026
  10. kb.synology.com: vpnplus_server_standardvpn?version=1_3 · checked Nov 19, 2026
  11. kb.synology.com: How_can_I_connect_Synology_Router_to_a_VPN_server · checked Nov 19, 2026
  12. help.ui.com: 7951513517079 UniFi Gateway Introduction to VPNs · checked Nov 19, 2026
  13. help.ui.com: 115005445768 UniFi Gateway WireGuard VPN Server · checked Nov 19, 2026
  14. wireguard.com: www.wireguard.com · checked Nov 19, 2026
  15. openvpn.net: how to · checked Nov 19, 2026
  16. support.linksys.com: 3773 en · checked Nov 19, 2026
  17. support.linksys.com: 6710 en · checked Nov 19, 2026

RouterPanel. "How to set up a VPN on a router." Updated Nov 19, 2026. https://howtosetuparouter.com/vpn-on-router/