A router table is the woodworking tool, not the network box. If you came for Wi-Fi, the definition of a network router is the page you want. For a square, safe cut: level the insert plate flush, fit the smallest ring the bit clears, close the fence on the bit and feed from the right, slowing the motor as the bit widens.
A router table is the workshop one
A router table holds the motor upside down under a flat top, with the bit standing up through an insert plate. The fence gives the work a straight edge to run against and holds it over the bit. That inversion puts the cutter where you can guide the work past it with both hands on the stock. Nothing here applies to the network box, including its firmware updates. Get the plate, ring and fence right first.
Level the plate and fit the ring
A plate that stands proud catches the workpiece; one that rocks does the same. Work from under the top and bring the plate levelers up until the plate is flush on every edge and all the screws bear equally. Rockler checks all edges before the plate is secured; Kreg asks for equal contact from all eight set screws.
Fit the reducing ring next. Kreg uses the smallest opening the bit will pass, closest to the bit diameter; a wide gap around the bit lets the work tip in and kick back. Rockler forbids any cut without a ring in place. Kreg sells the plate undrilled or predrilled for a Kreg, Triton, Porter-Cable or Bosch router; the undrilled plate is drilled to the motor's base so the hole pattern matches.
- Back the plate levelers down and lift the plate.
- Drill an undrilled plate for the motor's base if it is new.
- Fit the smallest ring the bit clears.
- Set the plate in and bring every leveler up until the plate is flush all round.
- Turn the bit by hand to check it clears the ring, then secure the plate.
Set the fence
Close the fence faces until they almost touch the bit. The two faces adjust independently; lock them and turn the bit by hand to prove clearance. For a straight edge, rout with the bit housed in the fence and the work against it.
Bit height and depth of cut
Choose the shank before the height. A 1/2 in shank has nearly four times the surface area of a 1/4 in shank and is the stronger choice where a bit is offered in both; Whiteside sets the 1/2 in threshold at bits over 3/4 in. Only use a shank that matches the fitted collet. Bosch asks for at least 5/8 in of the shank seated in its 1617/1618 collets.
A groove, dado or rabbet comes out cleaner in several passes, raising the bit or moving the fence between them. The Freud guide caps a pass at the bit's diameter and the Makita trimmer caps a groove at 3 mm. Box-joint and dovetail work has its own hardware: Rockler sells a box-joint jig for the router table, and dovetail pattern bits with a guide bearing for use with dovetail jigs. The jig works one notch per pass, fitting the notch just cut over the indexing key.
Speed by bit diameter
Top speed is the dial at the top of its range. Drop the speed as the bit grows; a wide bit at full speed burns and can shed teeth. Both makers below print ceilings of their own, though Kreg leaves four bands blank; set the dial at or under the figure printed for your diameter.
| Bit diameter | Kreg PRS2100 maximum | Amana Tool maximum |
|---|---|---|
| Up to 1 in | 24,000 rpm | 28,000 rpm |
| 1 in to 1-1/4 in | not printed | 28,000 rpm |
| 1-1/4 in to 2 in | 18,000 rpm | 28,000 rpm |
| 2 in to 2-1/4 in | not printed | 22,000 rpm |
| 2-1/4 in to 2-3/8 in | 16,000 rpm | 22,000 rpm |
| 2-3/8 in to 2-1/2 in | 16,000 rpm | 19,000 rpm |
| 2-1/2 in to 2-3/4 in | not printed | 19,000 rpm |
| 2-3/4 in to 3 in | not printed | 16,000 rpm |
| 3 in to 3-1/4 in | 12,000 rpm | 16,000 rpm |
| 3-1/4 in to 3-1/2 in | 12,000 rpm | 15,000 rpm |
| 3-1/2 in to 3-5/8 in | not printed | 15,000 rpm |
| Over 3-5/8 in | not printed | 13,000 rpm |
A Woodcraft speed chart prints lower ranges for bits generally: 22,000 to 24,000 rpm up to 1 in, 18,000 to 22,000 rpm from 1 to 2 in, 12,000 to 16,000 rpm from 2 to 2-1/2 in and 8,000 to 12,000 rpm from 2-1/2 to 3-1/2 in, each a maximum. A bit's own mark wins: the Freud 99-036 set is marked 16,000 rpm and the Whiteside 3000 template bit asks for 16,000 to 18,000 rpm. Rated speed must be at or above the router's top speed, or the bit can break.
Feed direction and kickback
The bit is the thing you do not touch. Feed the workpiece against the rotation of the bit, never with it: on a table, right to left across the front of the bit. Fed with the rotation, the bit grabs the work, throws it off the table and can pull your hand onto the cutter. That throw is kickback. Stand to the side of the cutter's line and keep the work hard against the fence. Feeding with the rotation on purpose is a climb cut; the feed direction guide sets the direction for each cut.
Push blocks and featherboards
Keep your hands back. A featherboard ahead of the bit presses the work against the fence and holds it down, and a push block carries the last few inches past the cutter with your hand above the bit. Set the first, shorter feather to graze the work so the longer feathers load properly. A push stick moves the ends of narrow stock when a block will not fit.
Router table or handheld
Large bits are barred from a hand-held router; mount the motor in a table instead. Bosch says a bit over 2 in will not pass its sub-base, and DeWalt caps its DW616 and DW618 at 2-1/2 in. Handheld, the router travels counter-clockwise on an outside cut and clockwise on an inside cut; under a table it flips to right to left. Edge profiles and raised panels want the table, where the fence and ring control a big cutter; Amana says raised-panel doors are possible only with the router mounted in a table. Pattern bits follow a template to duplicate a shape. A trim router still earns its place for flush trimming and profiling small cuts, the work Makita intends its RT0700C for.
Questions
Can you attach any router to a router table?
No. The motor needs a base you can bolt to a plate and a collet that matches your bits. Kreg sells the plate undrilled or predrilled for a Kreg, Triton, Porter-Cable or Bosch router. Where a bit is offered in both shanks, choose 1/2 in.
Do you really need a router table?
Not for every cut. A trim router handheld handles a 3 mm groove. You need the table once the bit gets large: over 2 in will not pass a handheld sub-base, and a 2-1/2 in cap applies to the DeWalt motors. The fence and ring make those cuts repeatable.