Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

2.4 GHz vs 5 GHz: picking the right band

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
The band is a radio setting: 5 GHz for speed at close range, 2.4 GHz for reach through walls.

By RouterPanel Editorial · Updated

Short answer

Set a device that sits in the same room with the router on 5 GHz, and leave 2.4 GHz for distance, walls and smart home kit. The 2.4 GHz band allows 1 W peak conducted for digital modulation but shares its span with everything else.

Set the device that sits in the same room with the router on 5 GHz, and leave 2.4 GHz for distance, walls and smart home kit. The 2.4 GHz band allows 1 W peak conducted but shares its small span with everything else.

The trade-off in one table

Signal loss and congestion decide the band. Lower frequency loses less through a wall but lives in a narrow, crowded strip; higher frequency carries more data but gives up distance.

The table sets the legal edges beside the power each band allows and turns both into the room that follows. A router obeys these limits; it does not beat them.

Legal band edges, channel rule and conducted-power cap per band, with the room each suits (47 CFR 15.247 and 15.407, checked 18 November 2026)
Band and legal edgesChannel ruleMaximum conducted powerRadar detectionRoom that follows
2.4 GHz: 2400 to 2483.5 MHzAt least 15 hopping channels for frequency-hopping systems1 W peak, digital modulation, antenna gain up to 6 dBiNot requiredFar rooms, garden, smart plugs
5 GHz low: 5150 to 5250 MHzNo fixed count for digital modulation1 W, outdoor access point, antenna gain up to 6 dBiNot requiredSame room
5 GHz mid: 5250 to 5350 MHzNo fixed count for digital modulation250 mW, or 11 dBm + 10 log B if lowerRequiredNext room, with a pause
5 GHz mid: 5470 to 5725 MHzNo fixed count for digital modulation250 mW, or 11 dBm + 10 log B if lowerRequiredNext room, with a pause
5 GHz high: 5725 to 5850 MHzNo fixed count for digital modulation1 WNot requiredSame room, no pause
6 GHz: 5925 to 7125 MHzNot printed in this section30 dBm e.i.r.p., 5 dBm per MHz, indoor access pointNot printed in this sectionSame room, line of sight

The 2.4 GHz band and the 5.725 to 5.850 GHz span each allow 1 W peak conducted for digital modulation. The spans between, 5.25 to 5.35 and 5.47 to 5.725 GHz, allow only 250 mW or less.

What each band carries

The 2.4 GHz span of 2400 to 2483.5 MHz is 83.5 MHz wide and is the band legacy devices understand: smart plugs, bulbs, cameras, doorbells. Frequency-hopping systems in it must use at least 15 channels, a narrow-slot design that suits sensor traffic and struggles in a busy room.

The 5 GHz spans run from 5150 to 5850 MHz, about 700 MHz, and suit a laptop, television or console near the router. The low edge allows 1 W at an outdoor access point with gain up to 6 dBi, while a client device there is held to 250 mW; the mid spans cap at 250 mW; the top span returns to 1 W with no radar detection.

6 GHz, 5925 to 7125 MHz, is the widest. An indoor access point may radiate 30 dBm e.i.r.p. under a 5 dBm per MHz density limit, and it suits the devices in the router's room.

Walls, floors and distance

Every wall, floor and door takes a bite, and the higher band loses more at each one. That sets the layout: 5 GHz for the router's room and the one next to it, 2.4 GHz for the far bedroom, the garage and the garden.

A floor sits on top of every wall on the way to it. Keep the router high, keep 5 GHz devices under it, and let 2.4 GHz serve the rooms across two walls. A room three walls away that needs high bandwidth wants a cable or a second node.

Interference on 2.4 GHz

The 2.4 GHz band is shared with microwave ovens, cordless phones, baby monitors, Bluetooth and every neighbour's access point. Its 83.5 MHz cannot absorb that many transmitters, so the band stays busy even when your own traffic is idle.

5 GHz and 6 GHz have far more room and fewer household tenants. The one shared-user problem on 5 GHz is radar in the two detection spans, where the router yields a channel. The yield is a short pause, but a video call can stutter.

Channels and overlap

A channel is a slot in the band, and slots overlap when they sit closer than their width. The 2.4 GHz rule asks frequency-hopping systems for at least 15 narrow slots, so the band is packed; the FCC allows 11 channels here, and only 1, 6 and 11 clear each other.

The 5 GHz band spreads its channels over 700 MHz and the 6 GHz band over 1200 MHz, so wide channels that would overlap on 2.4 GHz fit here. Set 2.4 GHz to 1, 6 or 11 and leave 5 GHz width at the default.

Radar decides the 5 GHz channel. The spans 5250 to 5350 and 5470 to 5725 MHz must detect radar; 5150 to 5250 and 5725 to 5850 MHz do not.

Split or shared SSID

A dual-band router ships with one SSID on both bands, and band steering moves each device to the band the router prefers. That is the right default for a household that does not want to think about it.

Split the names to place a device yourself: a distinct 5 GHz SSID for the television, console and laptop, the 2.4 GHz name for the smart kit. The router must allow it; a mesh system may not expose the control.

Pick a band per device

Use the device and its distance as the test.

Device and place against the band that fits, from the edges and caps above
Device and placeBandReason
Phone, laptop or television in the router's room5 GHzShort path, wide span
Console or work laptop on a call5 GHz, 5725 to 5850 MHz1 W, no radar pause
Smart plug, bulb, camera or doorbell2.4 GHzBuilt for legacy kit
Printer or older tablet2.4 GHzOlder radio
Camera at the front gate2.4 GHzOut of higher-band reach
Anything three rooms away or more2.4 GHzSurvives walls and floors

When to stop tuning and move the router

Stop changing bands when one room has a good 5 GHz signal and the far room a weak 2.4 GHz one. Position is the limit. Move the router central and high and check again before buying; the signal guide has the placement rules.

A booster repeats a weak signal, and many cheaper and older units effectively cut the bandwidth in half, so it is the last wireless step; see whether boosters work. A mesh node on wired backhaul beats it. The WAN cable and power jack matter more than any channel.

If the home is one room, start from the setup order instead.

Questions

Is 2.4 GHz or 5 GHz better for streaming?

5 GHz, if the player shares the router's room. A 4K stream needs a steady rate, and 5 GHz gives 700 MHz of room, with 1 W at its low edge for an outdoor access point. Behind three walls, drop to 2.4 GHz.

Should 2.4 and 5 GHz have the same name?

Yes for most homes, because band steering then places each device. Split them only to pin a television or console to 5 GHz by hand.

Key figures and scope

  • 1 W peak conducted, digital modulation: 2.4 GHz, 47 CFR 15.247(b)(3); gain up to 6 dBi, 47 CFR 15.247(b)(4); checked 18 November 2026.
  • 1 W, outdoor access point, gain up to 6 dBi: 5150 to 5250 MHz, 47 CFR 15.407(a)(1)(i), checked 18 November 2026.
  • 250 mW, or 11 dBm + 10 log B if lower: 5250 to 5350 and 5470 to 5725 MHz, 47 CFR 15.407(a)(2), checked 18 November 2026.
  • 1 W: 5725 to 5850 MHz, 47 CFR 15.407(a)(3)(i), checked 18 November 2026.
  • At least 15 hopping channels: 2.4 GHz hopping systems, 47 CFR 15.247(a)(1)(iii), checked 18 November 2026.
  • 30 dBm e.i.r.p. and 5 dBm per MHz: indoor 6 GHz access point, 47 CFR 15.407(a)(5), checked 18 November 2026.

Sources

Sources

  1. ecfr.gov: section 15.247 · checked Nov 19, 2026
  2. ecfr.gov: section 15.407 · checked Nov 19, 2026

RouterPanel. "2.4 GHz vs 5 GHz: picking the right band." Updated Nov 19, 2026. https://howtosetuparouter.com/2-4-vs-5-ghz/