Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

How to connect a router to a modem

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
The modem cable goes into the WAN port, never a LAN port.

By RouterPanel Editorial · Updated

Short answer

Power both devices off. Run coax from the wall outlet to the modem, then one Ethernet cable from the modem's LAN port to the router's WAN or Internet port. Power the modem on first, wait for its LEDs, then power on the router.

Power both devices off. Run coax from the wall outlet to the modem, then one Ethernet cable from the modem's LAN port to the router's WAN or Internet port. Power the modem on first, wait for its LEDs, then power on the router.

Which cable and which port

Amber means a cable you plug, and the cable here is one Ethernet patch lead, not a coax jumper. The port it reaches is the one printed WAN or "Internet"; cable modems label their side less clearly. ARRIS numbers its ports and Motorola calls its LAN side LAN, so read the label rather than reach for the nearest hole.

  1. Power the modem and the router off.
  2. Run the coax from the wall outlet to the modem's "Cable" connector.
  3. Plug one Ethernet cable into the modem's Ethernet jack, never a phone jack.
  4. Plug the other end into the router's WAN or "Internet" port.

Do not use a LAN port on the router. The LAN ports face your own devices; the WAN port is the only one that faces the line.

Log in at the local address

With the router powered, open its admin page in a browser from a device on the router's network. Netgear uses routerlogin.net or 192.168.1.1; TP-Link uses tplinkwifi.net or 192.168.0.1. On Netgear the user name is admin, and the password is the one you set during setup. Change both before you touch the wireless settings. The guide to connecting to a router covers the browser side when the page will not load.

Coax, fiber and the ONT handoff

Amber, this time at the wall outlet. One coaxial cable runs from the outlet to the modem's "Cable" connector and nowhere else; the router never sees coax. The DOCSIS 3.0 standard assumes a coaxial-based access network, either all-coax or hybrid-fiber/coax, and the modem's coax port is the interface to it.

Fiber changes the handoff, not the last cable. The fiber terminates on a Verizon Fios ONT, and the Ethernet cable runs into the WAN port, or a wall plate leading to the WAN port outside.

Upstream port labels, connectors and the printed power-on order, by maker and access type, checked 18 November 2026
Maker and deviceUpstream port labelConnector at the wallConnector at the routerPrinted power-on order
ARRIS Surfboard SB8200, cable modem"Cable"F-type coax to the outletRJ45 Ethernetnot printed
Motorola MB8600, cable modem (DOCSIS 3.1)"Coax Cable Connector"F-type coaxEthernet from one of four GigE LAN portsrouter on and cabled; modem off, powered on last
Netgear router with cable modemrouter "WAN / Internet"coaxRJ45 Ethernetcables, then power on
TP-Link router"Internet"coax on the modemRJ45 Ethernetmodem off while connecting, then on
Verizon Fios ONT, fiber"WAN port"optical fiber into the ONTEthernet cablenot printed

Motorola, TP-Link and Netgear each print a full sequence, and Motorola's runs the other way. The Cox page for the ARRIS SB8200 names both cables and leaves power order out. Where the column says not printed, follow the maker's own sheet if you have one.

Power-on order and the LED check

Red means reset, so leave the pinhole alone during this. TP-Link and Netgear both keep the modem off until the cable is seated and power the router after it. Motorola prints the reverse: its router stays powered on, the modem goes off, and the modem is powered on last.

  1. Keep both devices off until every cable is seated, unless the maker says otherwise.
  2. Switch the modem on and wait for its online LED to settle.
  3. Switch the router on.

The wait matters as much as the order: the modem's online LED blinks while it scans and stays solid once it is connected. The router's WAN LED is no guide to the line — on Netgear it goes solid amber as soon as it detects the cable to the modem, long before the internet is up.

Give the modem time after the online light settles before you judge anything. A WAN LED that never lights while the modem reports online usually means the cable is in a LAN port.

One router or two: bridge and double NAT

Two routers in line mean two NAT layers, and the inner one cannot open ports through the outer one. When the ISP supplied a gateway that also routes, put it in bridge mode so the router you add holds the only NAT. Where the gateway cannot bridge, run the second unit in access-point mode and let the gateway route. A plain modem has nothing to bridge. The modem versus router page sets out which box does which job.

Set the network name and password

Teal is the radio. In the admin page, open the wireless or Wi-Fi section. The network name is what every phone and laptop will list, so use something that identifies the flat rather than your surname. The password field takes the pre-shared key; choose WPA3 where the page offers it, otherwise the strongest encryption available, and a long key rather than a word. Save, then rejoin from each device. The Wi-Fi password page has the field names for the common brands.

When there is no internet after cabling

Check the port before the router. A cable in a LAN port instead of the WAN port gives a link light and no internet, because the router is only talking to itself. Swap it and retest. Second, the modem: if its online LED never settles, the fault is on the line and no router setting will fix it. Third, the order: power the modem off, then on, then the router. A double NAT from the earlier section also looks like a broken line at the far devices. The not connecting page takes the isolation test from there.

Questions

Do I need a modem to connect a router?

Yes, unless the box you already have combines both. The modem turns the line into a signal the router can use; a router alone has no upstream to share.

Can you connect another router to a modem router?

Yes, but not into the first box's WAN port while it still routes. Bridge the first box, or run the second one as an access point, or the two NAT layers fight.

Sources

  1. kb.netgear.com: What do the LEDs on my NETGEAR router mean · checked Nov 19, 2026
  2. arris.my.salesforce-sites.com: SB8200 First Time Installation · checked Nov 19, 2026
  3. cox.com: arris sb8200 · checked Nov 19, 2026
  4. manuals.plus: 5b6aeeeb7131e9aeaba5efb4864a89d7b18588d34e60ebeb83967be4b2684639 · checked Nov 19, 2026
  5. en-us.support.motorola.com: 177990 · checked Nov 19, 2026
  6. netgear.com: connecting cable modem and router · checked Nov 19, 2026
  7. tp-link.com: 3841 · checked Nov 19, 2026
  8. verizon.com: ont · checked Nov 19, 2026
  9. verizon.com: knowledge base 312255 · checked Nov 19, 2026
  10. cablelabs.com: CM SP OSSIv3.0 I05 071206 · checked Nov 19, 2026

RouterPanel. "How to connect a router to a modem." Updated Nov 19, 2026. https://howtosetuparouter.com/connect-modem/