Put the first node beside the modem, plug the modem's lead into its WAN port, and add satellites one at a time until the weak rooms hold a signal. Keep one network name, and put each node inside the maker's printed spacing. A mesh set is several boxes on one SSID, and the handoff between them is automatic, but the placement is what decides whether the set works.
What a mesh system does
A mesh system is two or more boxes sold together and set to broadcast the same SSID. One node holds the modem and each satellite repeats the signal further into the home, so a phone in a far room associates with the nearest node instead of straining for the router.
The SSID is the part a reader sees on the phone, and it stays the same across every node. The routing behind it is what moves as the reader walks, and it moves without the reader choosing a new network.
A wireless satellite spends one radio listening and another repeating. That relay is the weak point of the whole system, because every hop takes airtime the clients cannot use, and a second hop takes it twice. The cable from the modem and the first node's place beside it are covered in set up a router.
Two mistakes break the relay. A node too far arrives with a weak signal and repeats a weak one; a node too close competes for the same air. NETGEAR names both failures in one sentence and gives no number.
Linksys measures the same idea in rooms and floors rather than feet, and asks for nodes within two rooms or one floor of each other.
How many nodes your home needs
Count weak rooms rather than floor area. A node belongs where the signal already falls away, not beside the router that already covers the room it stands in.
Google puts points about 2 to 3 rooms apart, and tightens that to 1 or 2 rooms in a congested apartment.
eero asks for 20 to 30 feet between units and never more than 50. If three nodes cannot sit inside that band, plan on two nodes and a cable instead.
Start with the main node and one satellite. Add a third only when a room still drops after the second is placed and checked, because nodes placed too close together create interference, in NETGEAR's words, rather than coverage.
Spacing rules the makers print
Read the maker's figure before the box leaves the carton. The table collects the ceiling each one prints, beside the kind of home and node the figure is written for: most rows are a limit to stay inside, not a target.
| Maker | Printed spacing ceiling | Home size the figure targets | Limit and check date |
|---|---|---|---|
| NETGEAR | Not too far, not too close; no distance printed | Satellites and extenders in a home already covered by a router | Qualitative; no numeric band on the page; checked 18 November 2026 |
| TP-Link | No more than 50 ft apart, wireless | Whole-home Deco kits | Distance becomes more flexible with Ethernet backhaul; checked 18 November 2026 |
| ASUS | Between the router and the dead zone | AiMesh nodes added to an AiMesh router | Qualitative; move the node closer if its own reception is poor; checked 18 November 2026 |
| Google Nest Wifi | About 2 to 3 rooms apart; 1 to 2 rooms in a congested flat | Nest Wifi and Google Wifi points in a house with a weak far end | Room count, not a distance; put the point halfway toward the weak area; checked 18 November 2026 |
| Google Nest Wifi, placement page | No more than 2 rooms from the router or another point | Nest Wifi router and points in a whole home | Room count, not a distance; checked 18 November 2026 |
Google's second page repeats the same limit inside its placement steps: no more than 2 rooms away from the router or another point, with the point halfway toward the weak area. Both Google pages agree on the figure.
ASUS sends the node between the router and the dead zone, and moves the node closer when its own reception is poor. Google says the same in another shape: put the point halfway toward the weak area, not inside the weak area itself. A node in the weakest corner has the worst possible link back to the router, and it repeats that bad link to the room.
The radio also loses to the building. One concrete wall can take 10 to 20 dB out of 2.4 GHz and 20 dB or more out of 5 GHz in TP-Link's figures, which depend on the thickness and density of the wall. Stucco with wire mesh, brick, concrete and metal lath absorb heavily; drywall and soft insulation take the least.
Appliances matter as much as masonry. Keep at least 1 to 2 m from a microwave, a television, a cordless phone and a baby monitor, and at least 1 m from an aquarium or a water dispenser. A refrigerator, a mirror or a large pane of glass is a poor neighbour for a node.
The floor counts too. eero asks for the unit halfway between floor and ceiling rather than on the ground, because the radio leaves the box along its own plane.
Set up with the vendor app
The makers here run the set from a phone app: eero and Google Home keep the network in the handset app, and ASUS exposes its access point switch in the router app.
- Put the first node beside the modem, on a shelf rather than on the floor.
- Plug the modem's Ethernet lead into the node's WAN port, then power the node.
- Wait for the power LED to stop flashing; on TP-Link's Archer AX10 and AX1500 a flashing power light means the node is still starting or updating.
- Open the maker's app, and create the network name and passphrase.
- Add one satellite, carry it to the outer room, and hold it in place while the app reads the signal between the two nodes.
- Move the satellite a room closer if the app marks the link as weak, and recheck.
- Repeat for each further satellite, then run the update the app offers before using the network in earnest.
Parental controls, device names and QoS are in the same app. Set them after the network is up rather than during the join, so a stalled wizard never leaves the set half built.
A weak reading means move the satellite and recheck.
Wire the backhaul
The LAN port on the main node takes an Ethernet cable to the satellite. If a satellite labels its single port WAN, that is the port to use, because it is the upstream side of that box. The WAN port on the main node still belongs to the modem.
A cable run has a hard limit of 100 m including the patch cords, and the figure is a maximum channel distance rather than a target. A run through a wall should use cable rated for the space.
With a cable in the link, the wireless spacing rule relaxes. TP-Link says the distance between Deco units becomes more flexible with Ethernet backhaul, and the satellite can then sit in the weak room itself. That is the whole gain: the node no longer has to hear the network well, because the cable already carries the network.
Ethernet also does not halve the relay: the far room gets the full rate of the node instead of half.
The Ethernet standard itself names the cable: 1000BASE-T runs on Category 5e, and Category 6 is the minimum for 10GBASE-T. Match the cable to the port on the box rather than to the grade on the jacket.
Where no cable reaches, powerline or MoCA carries the backhaul over the wiring that already exists. Neither makes the line coming in any faster, but either can beat a second wireless hop: TP-Link says powerline is more stable and lower-latency than an extender under good conditions, and that a home with old wiring or outlets on separate circuits may find a Wi-Fi extender performs better. The options are set out in improve your Wi-Fi signal.
One SSID and roaming
The SSID stays the same on every node and on both bands, and the passphrase is set once. The client chooses the node as it moves; there is no second network to join by hand and no extender name to remember.
Roaming is the client's decision, not the system's. A phone that clings to a distant node keeps it until the link fails, and a system that hands off early is tuned to drop the client sooner.
WPA3 is mandatory on Wi-Fi CERTIFIED devices, requires protected management frames, and disallows the legacy protocols. WPA2 was still mandatory in the same certification as of 2018, and every certified device has shipped with it since 2006. A mixed WPA2/WPA3 mode leaves room for old plugs and phones beside the newer standard.
A guest SSID created in the app keeps visitors off the main name. Both the Google Home app and the eero app run a guest toggle, and both point to a guest password different from the main one. The steps for the main passphrase are in change your Wi-Fi password.
Can you add mesh to an existing router?
The WAN port on the first router still faces the modem after any change here; what changes is which box does the routing. You can add mesh in one of two ways: put the mesh set into access point mode behind the old router and let the old box keep the routing, or add nodes from the same maker as the router already in place.
Access point mode is the general answer. NETGEAR has the switch, and it turns off the guest network, site blocking and the VPN service while the box runs as a plain access point. TP-Link puts the same switch under Operation Mode and the Access Point Mode entry, and ASUS exposes it in the router app on some models only.
In access point mode the second box stops routing, so DHCP stays with the old router and the two do not fight over addresses. Running both as routers gives a double NAT, and NETGEAR lists port forwarding and online games among what it disrupts; that is why a mesh set behind a working router is better bridged than stacked.
The mesh nodes then carry one SSID from the old router's LAN side, and the handoff works as it would in a full mesh. A Starlink router has its own version of the same idea, called Bypass Mode.
What mesh does badly
Mesh is not the cheap answer. An extender costs less, and for one dead zone it is enough, but it loses half the speed to overhead, in NETGEAR's phrase, so the room gets the coverage at a reduced rate. The pairing steps are in set up a Wi-Fi extender.
TP-Link puts an extender 25 to 40 ft from the router with external antennas and 20 to 35 ft with internal ones, when the router signal is still strong at that distance, and never at the outer edge of the router's range. The full comparison is in Wi-Fi extender or mesh.
Firmware is the maintenance chore nobody plans for. The nodes need updates like any router, and every maker hides the path in a different place: NETGEAR in the Nighthawk app or under ADVANCED, TP-Link under Firmware Upgrade, ASUS under Administration, Linksys under Connectivity. Do not cut power while the power LED flashes during an upgrade. The sequence for each is in update your router's firmware.
Parental controls and QoS are app settings and cannot exceed the line. QoS sets the total bandwidth for the connection and shares it out, giving a device more when the network is overloaded; it cannot make the plan larger, and a parental filter on a saturated link still leaves the link saturated.
The internet plan is the real ceiling. A GPON line runs at nominal rates of 2.488 Gbit/s down and 1.244 Gbit/s up, and DOCSIS 3.1 is 10 Gbps down and up to 1 Gbps up; no node count changes either figure.
The reset pinhole is the red route, and hold times differ by maker. eero asks about 15 seconds with the LED flashing red, and Nest Wifi asks 10 seconds (12 on Nest Wifi Pro). Do not unplug during the Nest reset, and the older Google Wifi point and OnHub carry their own caution: hold the button more than 15 seconds and the device flashes a warning colour and will not reset. A reset wipes the name and passphrase, so have the app ready before the paperclip comes out.
Questions
Which is better, a WiFi extender or mesh?
An extender is cheaper and suits one dead zone, but it loses half the speed to overhead and leaves the room at a reduced rate. Mesh keeps one name and hands the client between nodes, and it costs more. The number of weak rooms decides, and one room is extender work.
Can I connect mesh WiFi to an existing router?
Yes, in access point mode. Switch the mesh set to access point mode, cable its main node to a LAN port on the old router, and let the old router keep the routing. NETGEAR and TP-Link both document the switch, and ASUS puts it in its app on some models. Bridged this way, the nodes carry the SSID without a double NAT.