Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

Does unplugging a router reset it?

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
Power is not reset: settings sit in memory and survive the plug.

By RouterPanel Editorial · Updated

Short answer

Unplug the power lead at the router, wait 30 seconds and plug it back in: the settings stay. Only the reset pinhole, held for the maker's printed time, erases the Wi-Fi name, passwords and internet settings. A Starlink Gen 2 resets on six power cycles.

No, not on an ordinary router. Pulling the plug is a restart: the Wi-Fi name, the Wi-Fi password and the admin password all survive the next boot. Only the reset pinhole, held for the time the maker prints, wipes them. The exception is Starlink Gen 2, which has no reset button and resets after six power cycles.

What unplugging does

A power cycle means pulling the power lead at the router. It is the first move for a stalled page, a device that will not join or Wi-Fi that dies in one room.

  1. Pull the power plug from the router.
  2. Wait 30 seconds.
  3. Plug it back in and let the lights settle.
  4. Rejoin with the saved password.
Power cycle against factory reset, with the reset procedure and hold time each maker prints (checked 18 November 2026)
ActionWhat you doHold
Power cycle, ordinary routersPull the plug at the router, wait 30 seconds, plug back innone
NETGEARPower light on; hold Reset on the back with a paper clip7 seconds
TP-LinkPowered on, hold Reset until the SYS LED quick-flashesMore than 10 seconds
Linksys Smart Wi-FiAdmin page Diagnostics, Reset; or hold Reset and releaseAbout 10 seconds
ASUS (RT-AC66U B1 page)Admin page Administration, Restore; or hold RESET until the LED flashes5 to 10 seconds
D-Link DIR seriesPaper clip in the recessed reset hole, then releaseAbout 10 seconds, 7 on the DIR-878
Google Nest WifiHome app: Factory reset network; bottom button as fallback10 seconds on the button (Nest Wifi router; 12 on Pro)
eeroHold Reset until the LED flashes redAbout 15 seconds
Xfinity WiFi GatewayUnplug, hold Reset at least 15 s, release, plug in, hold 30 sAt least 15 seconds, then 30
Verizon RouterPowered on, hold the rear Reset, then wait15 seconds
Starlink Gen 2Unplug and replug six times, 2 to 3 seconds apartSix cycles

What a factory reset does

Red is the pinhole, recessed: a paper clip hole on D-Link, a button on the back elsewhere. On eero the button sits on the back on the first generation, the Pro, PoE 6, PoE 7, PoE Gateway, Max 7 and Pro 7, on the side on a Beacon, and on the bottom on the eero, 6, 6 extender, 6+, Pro 6, Pro 6E, 7 and Outdoor 7; Nest Wifi puts its button on the bottom. Held on a powered router, it wipes the SSID, both passwords and the internet settings, and falls back to the label's credentials. Every device drops and stays offline until set up again.

A reset reboots the router, but it does more than a reboot: the configuration goes, the firmware stays.

Hold times the makers print

Hold times are printed, not guessed: NETGEAR seven seconds, TP-Link more than ten, eero and Verizon fifteen; Xfinity wants at least fifteen unplugged and thirty more plugged in. The table above holds the rest.

Watch the light, not the clock: the SYS LED quick-flashes on TP-Link, the power LED flashes on ASUS and turns orange on D-Link, the eero LED flashes red.

Which one to use

Restart anything that recovers by itself: a page that will not load, one dead room, a console that dropped off. Reset when the admin password is lost, the router came from someone else or you are passing the box on. On a router that will not connect it is the last step.

Back up first. Take the save where the admin page offers it: Restore/Save/Upload Setting on ASUS, Backup and Restore on TP-Link. Write down the Wi-Fi name and password, the admin password and any port forwards. Afterwards set a new Wi-Fi password and work through a router that is not connecting; the full sequence is in how to reset a router.

Questions

Will I lose the Wi-Fi password if I unplug the router?

No. The password and the network name are stored and come back at boot; only the reset pinhole takes them. Starlink Gen 2 is the exception.

How long do I hold the reset button?

As long as the maker prints: seven seconds on NETGEAR, more than ten on TP-Link, fifteen on eero and Verizon. Release when the status light signals.

Sources

  1. kb.netgear.com: How do I perform a factory reset on my NETGEAR router · checked Nov 19, 2026
  2. tp-link.com: 497 · checked Nov 19, 2026
  3. support.linksys.com: 304 en · checked Nov 19, 2026
  4. asus.com: 1000925 · checked Nov 19, 2026
  5. support.dlink.com: FAQView.aspx?f=ge3DgZLoXqQZEsxSPMR6WQ%3D%3D · checked Nov 19, 2026
  6. support.google.com: 6246619?hl=en · checked Nov 19, 2026
  7. eero.com: how do i reboot or reset my eero · checked Nov 19, 2026
  8. xfinity.com: wifi change admin tool · checked Nov 19, 2026
  9. verizon.com: router factory reset · checked Nov 19, 2026
  10. starlink.com: d68ed178 4d54 b486 b7d8 2a6273917632 · checked Nov 19, 2026

RouterPanel. "Does unplugging a router reset it?." Updated Nov 19, 2026. https://howtosetuparouter.com/reset-router/does-unplugging-router-reset-it/